Dell Networking S6000 System Скачать руководство пользователя | Manualshive

Страница: 271 / 1510

background image

in which you are creating the rule is applied to the monitored
interface.

Defaults

By default, 10 ACL logs are generated if you do not specify the threshold explicitly.

The default frequency at which ACL logs are generated is five minutes. By default,
flow-based monitoring is not enabled.

Command
Modes

CONFIGURATION-STANDARD-ACCESS-LIST

Command
History

Version 9.4(0.0)

Added support for flow-based monitoring on the S4810,
S4820T, S6000, and Z9000 platforms.

Version 9.3(0.0)

Added support for logging of ACLs on the S4810, S4820T,
and Z9000 platforms.

Usage
Information

When the configured maximum threshold is exceeded, generation of logs is
stopped. When the interval at which ACL logs are configured to be recorded
expires, the subsequent, fresh interval timer is started and the packet count for that
new interval commences from zero. If ACL logging was stopped previously
because the configured threshold is exceeded, it is re-enabled for this new interval.

If ACL logging is stopped because the configured threshold is exceeded, it is re-
enabled after the logging interval period elapses. ACL logging is supported for
standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure
ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable
logging for ACLs that are associated with egress interfaces.

You can activate flow-based monitoring for a monitoring session by entering
the

flow-based enable

command in the Monitor Session mode. When you

enable this capability, traffic with particular flows that are traversing through the
ingress and egress interfaces are examined and, appropriate ACLs can be applied in
both the ingress and egress direction. Flow-based monitoring conserves
bandwidth by monitoring only specified traffic instead all traffic on the interface.
This feature is particularly useful when looking for malicious traffic. It is available for
Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using
standard or extended access-lists. This mechanism copies all incoming or outgoing
packets on one port and forwards (mirrors) them to another port. The source port
is the monitored port (MD) and the destination port is the monitoring port (MG).

Related
Commands

— Assigns a IP ACL filter to deny IP packets.

ip access-list standard

— Creates a standard ACL.

Access Control Lists (ACL)

271

«
...
269
270
271
272
273
...
»

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Networking S6000 System

Бренд: Sams Страницы: 10

Бренд: FLIR Страницы: 2

Бренд: Yamamoto Electric Works Co., Ltd. Страницы: 15

Бренд: Cabletron Systems Страницы: 52

Бренд: Baxall Страницы: 33

Instant On 1930 24G 4SFP/SFP+l

Бренд: Aruba Страницы: 48

Бренд: UniFi Страницы: 8

Бренд: steute Страницы: 20

SEHI SEHI100TX-

Бренд: Cabletron Systems Страницы: 75

S5560S-EI Series

Бренд: H3C Страницы: 47

Бренд: DANLERS Страницы: 2

Бренд: LEGRAND Страницы: 4

KingShield T206-C

Бренд: Green Brook Страницы: 2

OMNICUBE F1DK102P

Бренд: Belkin Страницы: 21

Бренд: Qvis Страницы: 7

Area box distribution switch

Бренд: LEGRAND Страницы: 87

Бренд: Net Optics Страницы: 20

Бренд: Pakedge Device & Software Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды