Dell Networking S6000 System Скачать руководство пользователя | Manualshive

Страница: 1478 / 1510

background image

Defaults

Automatically assigned based on the MAC address of each VLT peer. The peer with
the lower MAC address is assigned unit 0; the peer with the higher MAC address is
assigned unit 1.

Command
Modes

VLT DOMAIN

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.2(0.0)

Introduced on the M I/O Aggregator. This command is
supported in Programmable-Mux (PMUX) mode only.

Version 9.0.2.0

Introduced on the S6000.

Version 9.0.0.0

Introduced on the Z9000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.8.0

Introduced on the S4810.

Usage
Information

When you create a VLT domain on a switch, Dell Networking OS automatically
assigns a unique unit ID (0 or 1) to each peer switch. The unit IDs are used for
internal system operations. Use the

unit-id

command to explicitly configure the

unit ID of a VLT peer. Configure a different unit ID (0 or 1) on each peer switch.

To minimize the time required for the VLT system to determine the unit ID assigned
to each peer switch when one peer reboots, use this command.

vlt domain

Enable VLT on a switch, configure a VLT domain, and enter VLT-domain configuration mode.

S6000

Syntax

vlt domain

domain-id

Parameters

domain-id

Enter the Domain ID number. Configure the same domain ID
on the peer switch. The range of domain IDs is from 1 to
1000.

Command
Modes

CONFIGURATION

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

1478

Virtual Link Trunking (VLT)

«
...
1476
1477
1478
1479
1480
...
»

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Networking S6000 System

GuardSwitch 300 Series

Бренд: GE Страницы: 4

MSD-804FD Series

Бренд: IDK Страницы: 133

Бренд: IDK Страницы: 150

Бренд: IDK Страницы: 101

Бренд: IDK Страницы: 85

Бренд: IDK Страницы: 40

Бренд: IDK Страницы: 97

Бренд: IDK Страницы: 117

Бренд: IDK Страницы: 77

Бренд: Alyseum Страницы: 7

Бренд: Erbe Страницы: 118

Бренд: StarTech.com Страницы: 16

Guard Master 440N-Z2NRS1A

Бренд: Allen-Bradley Страницы: 4

Бренд: 3Com Страницы: 74

Бренд: WAGO Страницы: 36

Бренд: Versa Technology Страницы: 26

CT.TS005.501401

Бренд: Talkswitch Страницы: 9

PSEN ma2.1p/ATEX

Бренд: Pilz Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды