ZyXEL Communications OLT2406 User Manual Download Page 95

Page: 95 / 766

Chapter 7 Status

OLT2406 User’s Guide

512 to 1023

This field shows the number of packets (including bad packets) received that were between 512
and 1023 octets in length.

1024 to 1518 This field shows the number of packets (including bad packets) received that were between

1024 and 1518 octets in length.

Giant

This field shows the number of packets (including bad packets) received that were between
1519 octets and the maximum frame size.

The maximum frame size varies depending on your

OLT

model.

Table 16 Port Status: Port Details (continued)

LABEL

DESCRIPTION

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT2406

Reviews:

Brands by name

Popular brands

ZyXEL Communications OLT2406, User Manual

Search results

Summary of Contents for OLT2406

Reviews:

Brands by name

Popular brands