ZyXEL Communications OLT2406 User Manual Download Page 148

Page: 148 / 766

Chapter 15 Bandwidth Control

OLT2406 User’s Guide

148

Egress Rate

Specify the maximum bandwidth allowed in kilobits per second (Kbps) for the out-going traffic
flow on a port.

Apply

Click

Apply

to save your changes to the OLT’s run-time memory. The OLT loses these changes if it is

turned off or loses power, so use the

Save

link on the top navigation panel to save your changes to

the non-volatile memory when you are done configuring.

Cancel

Click

Cancel

to reset the fields.

Table 44 Advanced Application > Bandwidth Control (continued)

LABEL

DESCRIPTION

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT2406

Reviews:

Brands by name

Popular brands

ZyXEL Communications OLT2406, User Manual

Search results

Summary of Contents for OLT2406

Reviews:

Brands by name

Popular brands