manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 163

 Chapter 19 Port Authentication

OLT2406 User’s Guide

163

Figure 102   

IEEE 802.1x Authentication Process 

19.1.2  MAC Authentication 

MAC authentication works in a very similar way to IEEE 802.1x authentication. The main difference is that 
the OLT does not prompt the client for login credentials. The login credentials are based on the source 
MAC address of the client connecting to a port on the OLT along with a password configured 
specifically for MAC authentication on the OLT.

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands