
Chapter 95 CFM Commands
OLT2406 User’s Guide
653
95.3 CFM
The following section lists the commands for this feature.
Table 351 CFM Commands
COMMAND
DESCRIPTION
M
P
ethernet cfm
Enables CFM on the OLT.
C
13
ethernet cfm md <1-4294967295>
format <dns|mac|string> name <
md-
name
> level <0-7>
Creates an MD (Maintenance Domain) with the
specified name and level number.
md-name
: Enters a domain name, MAC address
or a descriptive name for the MD.
C
13
ethernet cfm ma <1-4294967295>
format <vid|string|integer> name
<
ma-name
> md <
md-index
> primary-
vlan <1-4094>
Creates an MA (Maintenance Association) and
defines its VLAN ID under the MD. You can also
define the format which the OLT uses to send this
MA information in the domain (MD).
ma-name
: Enters a VLAN ID, a descriptive name
or a 2-octet integer for the MA.
Note: If you set the
format
to
vid
, the
VLAN ID should be the same as the
VLAN ID you use to identify the MA.
C
13
cc-interval
<100ms|1s|10s|1min|10min>
Sets how often an MEP sends a connectivity
check message (CCM).
C
13
id-permission < none | chassis |
management | chassis-management>
Sets what’s to be included in the sender ID TLV
(Type-Length-Value) transmitted by CFM
packets.
Select
none
to not include the sender ID TLV.
Select
chassis
to include the chassis
information.
Select
management
to include the management
information.
Select
chassis-management
to include both
chassis and management information.
C
13
mep <1-8191> interface port-
channel <
aid
> direction <up|down>
priority <0-7> cc-enable
Enables Connectivity Check (CC) to allow an
MEP sending Connectivity Check Messages
(CCMs) periodically to other MEPs.
aid
:
<ge|msc|pon>-<
slot
>-<
port
>
C
13
mep <1-8191> interface port-
channel <
aid
> direction <up|down>
priority <0-7> inactive
Disables a specified MEP.
C
13
mep <1-8191> interface port-
channel <
aid
> direction <up|down>
priority <0-7>
Sets an MEP in an MA.
up|down
: The traffic direction.
0-7
: The priority value of the CCMs or LTMs
transmitted by the MEP. 1 is the lowest, then 2, 0
and 3 ~ 7.
C
13
Summary of Contents for OLT2406
