manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 277

 Chapter 31 ONT VoIP

OLT2406 User’s Guide

277

re-
registration 
head start 
time

Enter the number of seconds (0-720) the OLT tries again to register the SIP account before the 
session ends.

host part uri

Configure the host or domain part of the SIP URI (from 1 to 63 characters).

sip registrar

Configure the IP address or URI (from 1 to 63 characters) of the SIP registrar server.

softswitch

Configure the SIP gateway softswitch vendor name code (4 characters).

caller id

Configure the list of supported caller ID (CID) features. 

cal-num

: Calling number

cal-nam

: Calling name

cid-blo

: CID blocking (both number and name)

cid-num

: CID number

cid-nam

: CID name

ACR

: Anonymous CID blocking

call waiting

Configure the list of supported call waiting features. 

cal-wai

: Call waiting

cid-ann

: Caller ID announcement

call progress 
or transfer

Configure the list of supported features for calls in progress.

3way

: 3-way calling

cal-tra

: Call transfer

cal-hol

: Call hold

cal-par

: Call park

not-dis

: Do not disturb

flash

: Flash on emergency service call

origin

: Emergency service origination hold

6way

: 6-way calling

call 
presentation

Configure the list of supported call presentation features.

spl-rin

: Message waiting indication splash ring

dia-ton

: Message waiting indication special dial tone

vis-ind

: Message waiting indication visual indication

cal-for

: Call forwarding indication

direction 
connect

Configure the list of direct connect features. 

enable

: Direct connect feature enabled

dia-opt

: Dial tone feature delay option

direction 
connect uri

Configure a direct connect URI (from 1 to 63 characters). Set a direct connect URI to use SIP to 
direct connect a VoIP Server.

bridged line 
agent uri

Set the bridged line agent URI (from 1 to 63 characters). An interaction SIP bridge enables agents to 
use an IP telephone at a remote location through a TCP/IP network to a Customer Interaction 
Center.

Table 114   Advanced Application > ONT VoIP > Voip-Sip-Profile (continued)

LABEL

DESCRIPTION

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands