manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 52

Chapter 2 Hardware Installation

OLT2406 User’s Guide

52

the regular DC power source and connect input 2 to a backup DC power source such as a battery. The 
connections are as follows:

1

Loosen the power module thumbscrews and remove the power module from the OLT. 

2

Remove the green power connector block from the front of the power module.

3

Connect power wires to the RTN power terminal on the power connector block and tighten the terminal 
screw.

4

Connect power wires to the -48 V power terminal on the power connector block and tighten the 
terminal screw.

5

Push the power connector block back into the front of the power module.

6

Slide the power module back into the OLT and tighten the power module thumbscrews.

7

Connect the other end of the RTN power wires to the positive terminal on the power supply.

8

Connect the other end of the -48 V power wires to the negative terminal on the power supply.

9

Repeat the previous steps for the second power module.

10

Turn on the power supplies.

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands