manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 488

Chapter 67 Port Mirroring

OLT2406 User’s Guide

488

67.3  Port Mirroring Command Examples

This example enables port mirroring and copies outgoing traffic from ge port 4 on the card in slot 6 to 
uplink port 3 on the MSC. Use “

msc-1-

<port>

” for an uplink port (“

msc-1-

” applies to the active MSC no 

matter which slot it is in). 

 

This example displays the mirror settings of the OLT after you configured in the example above.

OLT2406(config)# mirror-port

OLT2406(config)# mirror-port msc-1-3

OLT2406(config)# interface port-channel ge-6-4

OLT2406(config-interface)# mirror

OLT2406(config-interface)# mirror dir egress

OLT2406# show mirror

     Mirroring:  enable

  Monitor port:  msc-1-3

   Mirrored port: ge-6-4

         Ingress:

          Egress: ge-6-4

            Both:

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands