manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 485

 Chapter 66 Broadcast Storm Control

OLT2406 User’s Guide

485

66.3  Broadcast Storm Control Examples

Enable broadcast storm control on the OLT.      

Disable broadcast storm control on the OLT.     

Set broadcast storm control on a port (ge-5-1) which is active, to limit its broadcast type traffic with a 
threshold of 999 packets per second.     

storm-control counter <cr>

Enables storm control packet counting for the 
specified port.

C

13

storm-control logging <cr>

Enables storm control packet logging for the 
specified port.

C

13

no storm-control counter

Disables storm control packet counting for the 
specified port.

C

13

no storm-control logging

Disables storm control packet logging for the 
specified port.

C

13

Table 243   Broadcast Storm Control Commands (continued)

COMMAND

DESCRIPTION

M

P

OLT2406# configure

OLT2406(config)# storm-control

OLT2406(config)# no storm-control

OLT2406(config)# interface port-channel ge-5-1

OLT2406(config-interface)# broadcast-limit

OLT2406(config-interface)# broadcast-limit 999

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands