manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 710

Chapter 102 PPPoE IA

OLT2406 User’s Guide

710

Here are the PPPoE IA show commands.  

OLT2406# show pppoe intermediate-agent

Switch PPPoE IA is disabled

PPPoE IA access-node-identifier string: OLT2406

Operator configures the flexible syntax for PPPoE IA circuit-id: No

PPPoE IA is enabled in the following VLANs:  None

PPPoE IA circuit-id is enabled in the following VLANs:  None

PPPoE IA remote-id is enabled in the following VLANs:  None

PPPoE IA port setting is configured as following:

Interface 1:

        Trusted: No

        Circuit-id string:

        Remote-id string:

Interface 2:

        Trusted: No

        Circuit-id string:

        Remote-id string:

----------------------------------------------------------------------------------

-----------------------

Interface 36:

        Trusted: No

        Circuit-id string:

        Remote-id string:

OLT2406# show pppoe intermediate-agent ?

    <cr>                      Show PPPoE-IA configuration

    statistic                   Statistics

OLT2406# show pppoe intermediate-agent statistic ?

    <cr>                      Show PPPoE-IA statistics

    vlan                      VLAN configuration

OLT2406# show pppoe intermediate-agent statistic

OLT2406# show pppoe intermediate-agent statistic vlan 1

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands