manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 273

 Chapter 31 ONT VoIP

OLT2406 User’s Guide

273

Figure 165   

Advanced Application > ONT VoIP > VoIP Common Profile

The following table describes the labels in this screen.  

Table 113   Advanced Application > ONT VoIP > VoIP Common Profile

LABEL

DESCRIPTION

Name

Type the name of the profile.

min local 
port

max local 
port

Specify a range (1-65535) of RTP ports to use for voice traffic.

dscp mark

Specify the Diffserv code point (from 0 to 63) to use for outgoing RTP packets.

piggyback

Select this to turn on RTP piggyback events on or clear it to turn them off.

tone

Select this to turn the handling of tones through RTP tone events according to RFC 4733 on or clear 
it to turn it off.

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands