manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 268

Chapter 30 Error Disable

OLT2406 User’s Guide

268

Figure 162   

Advanced Application > Errdisable > CPU protection 

The following table describes the labels in this screen. 

Table 110   Advanced Application > Errdisable > CPU protection

LABEL

DESCRIPTION

Reason

Select the type of control packet you want to configure here.

Port 

This field displays the port number. * means all ports.

*

Use this row to make the setting the same for all ports. Use this row first and then make 
adjustments to each port if necessary. 

Changes in this row are copied to all the ports as soon as you make them.

Rate Limit (pkt/s)  Enter a number from 0 to 256 to specify how many control packets this port can receive or 

transmit per second.

0

 means no rate limit.

You can configure the action that the OLT takes when the limit is exceeded. See 

Section 30.4 on 

page 269

 for detailed information.

Apply

Click 

Apply

 to save your changes to the OLT’s run-time memory. The OLT loses these changes if it 

is turned off or loses power, so use the 

Save

 link on the top navigation panel to save your 

changes to the non-volatile memory when you are done configuring.

Cancel

Click 

Cancel

 to begin configuring this screen afresh.

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands