manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 124

Chapter 11 Static Multicast Forwarding

OLT2406 User’s Guide

124

Figure 77   

Static Multicast Forwarding to A Single Port

Figure 78   

Static Multicast Forwarding to Multiple Ports 

11.2  Configuring Static Multicast Forwarding

Use this screen to configure rules to forward specific multicast frames, such as streaming or control 
frames, to specific port(s).

Click 

Advanced Application 

>

 Static Multicast Forwarding

 to display the configuration screen as shown.

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands