Home
/
ZyXEL Communications
/
OLT2406
/
User Manual

ZyXEL Communications OLT2406, User Manual

Share

Page: 426 / 766

ZyXEL Communications OLT2406 User Manual Download Page 426

Chapter 55 IPv6

OLT2406 User’s Guide

426

The following table describes the multicast addresses which are reserved and can not be assigned to a
multicast group.

Loopback

A loopback address (0:0:0:0:0:0:0:1 or ::1) allows a host to send packets to itself. It is similar to “127.0.0.1”
in IPv4.

Unspecified

An unspecified address (0:0:0:0:0:0:0:0 or ::) is used as the source address when a device does not have
its own address. It is similar to “0.0.0.0” in IPv4.

EUI-64

The EUI-64 (Extended Unique Identifier) defined by the IEEE (Institute of Electrical and Electronics
Engineers) is an interface ID format designed to adapt with IPv6. It is derived from the 48-bit (6-byte)
Ethernet MAC address as shown next. EUI-64 inserts the hex digits fffe between the third and fourth bytes
of the MAC address and complements the seventh bit of the first byte of the MAC address. See the
following example.

FF05:0:0:0:0:0:0:2

All routers on a local site.

FF05:0:0:0:0:0:1:3

All DHCP severs on a local site.

Table 208 Reserved Multicast Address

MULTICAST ADDRESS

FF00:0:0:0:0:0:0:0

FF01:0:0:0:0:0:0:0

FF02:0:0:0:0:0:0:0

FF03:0:0:0:0:0:0:0

FF04:0:0:0:0:0:0:0

FF05:0:0:0:0:0:0:0

FF06:0:0:0:0:0:0:0

FF07:0:0:0:0:0:0:0

FF08:0:0:0:0:0:0:0

FF09:0:0:0:0:0:0:0

FF0A:0:0:0:0:0:0:0

FF0B:0:0:0:0:0:0:0

FF0C:0:0:0:0:0:0:0

FF0D:0:0:0:0:0:0:0

FF0E:0:0:0:0:0:0:0

FF0F:0:0:0:0:0:0:0

Table 209

MAC

00

: 13

: 49

: 12

: 34

: 56

Table 207 Predefined Multicast Address (continued)

MULTICAST ADDRESS

DESCRIPTION

«
...
424
425
426
427
428
...
»

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands