manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 93

 Chapter 7 Status

OLT2406 User’s Guide

93

Figure 60   

Port Status: Port Details  

The following table describes the labels in this screen. 

Table 16   Port Status: Port Details

LABEL

DESCRIPTION

Port Info

Port NO.

This field displays the port number you are viewing.

Name

This field displays the name of the port.

Link

This field displays the speed (such as 

100M

 for 100Mbps, 

1000M

 for 1000 Mbps, 

2.5G

 for 2.5 Gbps, 

or 

10G

 for 10 Gbps) and the duplex (

F

 for full duplex or 

H

 for half). This field displays 

Down

 if the 

port is not connected to any device.

State

If STP (Spanning Tree Protocol) is enabled, this field displays the STP state of the port (see 

Chapter 

14 on page 131

 for more information). 

If STP is disabled, this field displays 

FORWARDING

 if the link is up, otherwise, it displays 

STOP

.

LACP

This field shows if LACP is enabled on this port or not. 

TxPkts

This field shows the number of transmitted frames on this port

RxPkts

This field shows the number of received frames on this port

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands