manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 743

 Chapter 110 Product Specifications

OLT2406 User’s Guide

743

110.3  DC Power Wire Specifications

The following table lists the specifications of the DC power wire. See 

Table 386 on page 741

 for the wire 

gauge.  

110.4  Power Consumption

The following table gives an overview of power consumption information.

110.5  Firmware Naming Conventions

A firmware version includes the model code and release number as shown in the following example.

Table 388   DC Power Wire Specifications 

ITEM

DESCRIPTION

Wire gauge

Make sure you use wires of the specified wire gauge.

Ground wire: 18 AWG or larger

Power wires: 18 AWG or larger

Table 389   Power Consumption Specifications

ITEM

MAXIMUM VALUE

QUANTITY

Total system power

185 Watts

1

Management card 

45 Watts

2 maximum

Fan module

18 Watts

1

GPON line card

18 Watts

4 maximum

GE line card

10 Watts

4 maximum

Firmware Version:  V4.00(AAVA.5)

"AAVA" is the model code.
"5" is this firmware's release number. This varies as new firmware is released. Your firmware's 
release number may not match what is displayed in this User's Guide.

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands