manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 289

OLT2406 User’s Guide

289

C

HAPTER

 35

ONT Reboot

35.1  Overview

Use this screen to restart an ONT without physically turning its power off, and load a firmware image 
when it reboots.

35.2  The ONT Reboot Screen

Click

 Advanced Application 

>

 ONT Reboot

 in the navigation panel to display the screen as shown.

Figure 174   

Advanced Application > ONT Reboot 

The following table describes the labels in this screen.  

Table 122   Advanced Application > ONT Reboot

LABEL

DESCRIPTION

Select the GPON interface that the ONTs are connected to.

ONT AID

This is the ONT’s ID in the format: uniport-<pon>-<ont>-<card>-<port>.

* means all ONTs.

Action

Select a fimware file, 

current Image

, 

Image1

, or 

Image2

, to load when the ONT reboot.

CheckApply

Select the ONT(s) to reboot.

Apply

Click 

Apply

 to reboot the ONT(s).

Cancel

Click 

Cancel

 to begin configuring this screen afresh.

Paging

Prev/Next

Click 

Prev

 or 

Next

 to show the previous/next screen if all status information cannot be seen in 

one screen.

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands