manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 175

 Chapter 21 Classifier

OLT2406 User’s Guide

175

Figure 110   

Advanced Application > Classifier 

The following table describes the labels in this screen. 

Table 57   Advanced Application > Classifier

LABEL

DESCRIPTION

Active

Select this option to enable this rule. 

Name 

Enter a descriptive name for this rule for identifying purposes. 

Packet 
Format

Specify the format of the packet. Choices are 

All

, 

Ethernet II tagged

 and 

Ethernet II untagged

.

A value of 

Ethernet II

 indicates that the packets are formatted according to RFC 894, Ethernet II 

encapsulation.

Layer 2

Specify the fields below to configure a layer 2 classifier.

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands