manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 731

 Chapter 109 Troubleshooting

OLT2406 User’s Guide

731

This table lists all log types.

This table lists all log messages and their corresponding categories, types, and severities.

6

IN: Informational, the syslog contains an informational message.

7

DE: Debug, the message is intended for debug-level purposes.

Table 384   Log Types

SYSTEM

INTERFACE

SWITCH

IP

Table 385   Log Messages

Category

Log Message

Type

Severity

cfm

CFM has defects

SWITCH

WARNING

cfm

CFM has no defects

SWITCH

WARNING

cfm

cfmFngStateProcess report defects

SWITCH

WARNING

ddmi

Abnormal RX power state at port

INTERFACE

NOTICE

ddmi

Abnormal RX power state at port has been cleared

INTERFACE

NOTICE

ddmi

Abnormal temperature state at port

INTERFACE

NOTICE

ddmi

Abnormal temperature state at port has been cleared

INTERFACE

NOTICE

ddmi

Abnormal TX bias state at port

INTERFACE

NOTICE

ddmi

Abnormal TX bias state at port has been cleared

INTERFACE

NOTICE

ddmi

Abnormal TX power state at port

INTERFACE

NOTICE

ddmi

Abnormal TX power state at port has been cleared

INTERFACE

NOTICE

ddmi

Abnormal voltage state at port

INTERFACE

NOTICE

ddmi

Abnormal voltage state at port  has been cleared

INTERFACE

NOTICE

interface

Port  link down

INTERFACE

DEBU

interface

Port  link up

INTERFACE

DEBU

interface

port link speed and duplex mode autonegotiation has failed

INTERFACE

WARNING

interface

port link speed and duplex mode autonegotiation has recovered 
to normal state

INTERFACE

WARNING

mstp

MSTP instance new root

SWITCH

NOTICE

mstp

MSTP instance topology changes

SWITCH

NOTICE

omci-alarm

15Ais (MEId) alarm

SYSTEM

WARNING

omci-alarm

15MBais (MEId) alarm

SYSTEM

WARNING

omci-alarm

15MRec (MEId) alarm

SYSTEM

WARNING

omci-alarm

2MAis (MEId) alarm

SYSTEM

WARNING

omci-alarm

2MRec (MEId) alarm

SYSTEM

WARNING

omci-alarm

34MAis (MEId) alarm

SYSTEM

WARNING

omci-alarm

34MRec (MEId) alarm

SYSTEM

WARNING

omci-alarm

45MAis (MEId) alarm

SYSTEM

WARNING

Table 383   Log Severity Levels

CODE SEVERITY

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands