manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 625

 Chapter 85 Access Control

OLT2406 User’s Guide

625

85.14  ONT ACL Commands

Use these commands to create ACL profiles for ONTs. 

Table 330   Remote Management Commands

COMMAND

DESCRIPTION

M

P

ont-acl-profile <profile-name>

Creates an ACL profile. 

profile-name

: less than 31 printable characters

C

13

inactive

Disables the ACL profile.

C

13

no inactive

Enables the ACL profile.

C

13

no interface

Restores the interface default setting for the ACL 
profile.

C

13

policy <drop|trust>

Specifies the actions for the ACL profile.

drop

: Discards the incoming packets.

trust

: Forwards the incoming packets.

C

13

no policy

Restores the policy default setting for the ACL 
profile.

C

13

interface <lan|wan|both>

Configures the interface(s) for the ACL profile.

C

13

ip-protocol <protocol>

Enters an IP protocol for the ACL profile.

See 

Table 331 on page 626

 for the list of IP 

protocol numbers.

protocol

: 0 ~ 255

C

13

no ip-protocol

Removes the IP protocol for the ACL profile.

C

13

counter <enable|disable>

Enables or disables packet counting for the ACL 
profile.

C

13

logging <enable|disable>

Enables or disables packet logging for the ACL 
profile.

C

13

src-mac-addr <mac>

Specifies a source MAC address range.

mac

: 00:00:00:00:00:00 ~ FF:FF:FF:FF:FF:FF

C

13

dest-mac-addr <mac>

Specifies a destination MAC address range.

mac

: 00:00:00:00:00:00 ~ FF:FF:FF:FF:FF:FF

C

13

src-ip-addr <ip> mask-bits <mask>

Specifies the mask bits of the source IP address, 
0-32.

C

13

dest-ip-addr <ip> mask-bits <mask>

Specifies the mask bits of the destination IP 
address, 0-32.

C

13

src-l4-port <port>

Specifies a layer 4 source port.

port

: 0-65535

C

13

dest-l4-port <port>

Specifies a layer 4 destination port.

port

: 0-65535

C

13

no src-mac-addr

Removes the source MAC setting.

C

13

no dest-mac-addr

Removes the destination MAC setting.

C

13

no src-ip-addr

Removes the source IP address setting.

C

13

no dest-ip-addr

Removes the destination IP address setting.

C

13

no src-l4-port

Removes the source L4 port setting.

C

13

no dest-l4-port

Removes the destination L4 port setting.

C

13

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands