manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 194

Chapter 24 VLAN Stacking

OLT2406 User’s Guide

194

Figure 118   

Advanced Application > VLAN Stacking 

The following table describes the labels in this screen. 

Table 67   

Advanced Application > VLAN Stacking

LABEL

DESCRIPTION

Port 

This field displays the port number.

*

Settings in this row apply to all ports.

Use this row only if you want to make some settings the same for all ports. Use this row first to set the 
common settings and then make adjustments on a port-by-port basis. 

Note: Changes in this row are copied to all the ports as soon as you make them.

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands