manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 236

Chapter 27 IP Source Guard

OLT2406 User’s Guide

236

Figure 140   

Advanced Application > IP Source Guard > ARP Inspection > VLAN Status

The following table describes the labels in this screen. 

27.8  ARP Inspection Log Status

Use this screen to look at log messages that were generated by ARP packets and that have not been 
sent to the syslog server yet. To open this screen, click 

Advanced Application > IP Source Guard > ARP 

Inspection > Log Status

.

Table 88   Advanced Application > IP Source Guard > ARP Inspection > VLAN Status

LABEL

DESCRIPTION

Show VLAN range

Use this section to specify the VLANs you want to look at in the section below.

Enabled VLAN

Select this to look at all the VLANs on which ARP inspection is enabled in the section below.

Selected VLAN

Select this to look at all the VLANs in a specific range in the section below. Then, enter the 
lowest VLAN ID (

Start VID

) and the highest VLAN ID (

End VID

) you want to look at.

Apply

Click this to display the specified range of VLANs in the section below.

VID

This field displays the VLAN ID of each VLAN in the range specified above.

Received

This field displays the total number of ARP packets received from the VLAN since the OLT 
last restarted.

Request

This field displays the total number of ARP Request packets received from the VLAN since 
the OLT last restarted.

Reply

This field displays the total number of ARP Reply packets received from the VLAN since the 
OLT last restarted.

Forwarded

This field displays the total number of ARP packets the OLT forwarded for the VLAN since the 
OLT last restarted.

Dropped

This field displays the total number of ARP packets the OLT discarded for the VLAN since the 
OLT last restarted.

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands