manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 715

 Chapter 105 IP and MAC Anti-Spoofing

OLT2406 User’s Guide

715

The OLT drops packets from source IP addresses or MAC addresses listed in the exclusive entries and 
forwards others. 

105.2  IP and MAC Anti-Spoofing Configuration

105.2.1  Activating IP and MAC Anti-Spoofing 

These commands activate and de-activate anti-spoofing on the OLT.  

These commands activate and de-activate anti-spoofing on the specified port.   

Note: You must activate anti-spoofing on both the OLT and the port.

105.2.2  VLAN and MAC Spoofing Settings

These commands configure an anti-spoofing entry on a port-channel interface.    

MAC-Only

(Exclusive)

The OLT allows all packets unless the source MAC address is in the list.

IP-MAC

(Exclusive)

The OLT allows non-IP packets. The OLT also allows IP packets unless the source MAC address 
and source IP address are in the list.

Table 376   Results for Exclusive Anti-Spoofing Entries (continued)

SETTING

RESULT

OLT2406# config

OLT2406(config)# anti-spoofing

OLT2406(config)# no anti-spoofing

OLT2406#config

OLT2406(config)#interface port-channel <AID>

OLT2406(config-interface)# anti-spoofing

OLT2406(config-interface)# no anti-spoofing

OLT2406#config

OLT2406(config)# interface port-channel <AID>

OLT2406(config-interface)# anti-spoofing <inclusive|exclusive> ip <ip> mac <mac-

addr> 

OLT2406(config-interface)# anti-spoofing <inclusive|exclusive> ip <ip> 

OLT2406(config-interface)# anti-spoofing <inclusive|exclusive> mac <mac-addr>

OLT2406(config-interface)# anti-spoofing inclusive oui-mac <oui-mac-addr>

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands