manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 539

 Chapter 76 Multicast

OLT2406 User’s Guide

539

The following table shows the IGMP commands for an interface port channel.   

Table 276   IGMP Commands on Interface Port Channel

COMMAND

DESCRIPTION

M

P

remote uniport <aid>

Configures UNI port settings.

aid: uniport-<pon>-<ont>-<card>-<port>

C

13

igmpchannel <

uni-vid

> <cr>

Creates an IGMP channel on this port.

uni-vid

: The default VLAN ID for IGMP reports, 

that is Join and Leave packets. You must first 
create the VLAN using the vlan command 
under the 

remote uniport

 command. 

(Required.)

C

13

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands