manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 583

 Chapter 79 PON DDMI

OLT2406 User’s Guide

583

no interface transceiver-ddmi 

<

aid

>

Deletes the interface transceiver threshold 
configuration for the specified port.

aid

: <ge|msc|pon>-<

slot

>-<

port

>

C

13

no interface transceiver-ddmi all

Deletes all interface transceiver threshold 
configuration.

C

13

show interfaces transceiver <

aid

>

Displays real-time SFP (Small Form Factor 
Pluggable) transceiver information and 
operating parameters on specified SFP port(s). 
The parameters include, for example, module 
temperature, module voltage, transmitting and 
receiving power.

aid

: 

slot-<

slot

> | <ge|msc|pon>-<

slot

>-

<

port

>

E

3

Table 300   PON DDMI Commands (continued)

COMMAND

DESCRIPTION

M

P

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands