manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 482

Chapter 64 Bandwidth Control

OLT2406 User’s Guide

482

bandwidth-threshold ingress 

<

kbps

>

Sets the interface’s bandwidth rate threshold for 
incoming traffic.

The range of an XE port is from 

0

 to 

10000000

 

Kbps.

The range of a GPON port is from 

0

 to 

2500000 

Kbps.

The range of a GE port is from 

0

 to 

1000000

 

Kbps.

C

13

no bandwidth-threshold egress 

Removes the interface’s bandwidth rate 
threshold for outgoing traffic.

C

13

no bandwidth-threshold ingress

Removes the interface’s bandwidth rate 
threshold for incoming traffic.

C

13

show interfaces config <

aid

> 

bandwidth-threshold

Displays the bandwidth control configuration for 
the specified port.

aid

: 

<msc|ge|pon>-<

slot

>-<

port

>

E

13

Table 241   Bandwidth Control Commands  (continued)

COMMAND

DESCRIPTION

M

P

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands