manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 439

OLT2406 User’s Guide

439

55.4  Example - Enabling IPv6 on Windows XP/2003

By default, Windows XP and Windows 2003 support IPv6. This example shows you how to use the 

ipv6 

install

 command on Windows XP/2003 to enable IPv6. This also displays how to  use the 

ipconfig

 

command to see auto-generated IP addresses.

IPv6 is installed and enabled by default in Windows Vista. Use the “ipconfig” command to check your 
automatic configured IPv6 address as well. You should see at least one IPv6 address available for the 
interface on your computer.

C:\>ipv6 install

Installing...

Succeeded.

C:\>ipconfig

Windows IP Configuration

Ethernet adapter Local Area Connection:

        Connection-specific DNS Suffix  . : 

        IP Address. . . . . . . . . . . . : 10.1.1.46

        Subnet Mask . . . . . . . . . . . : 255.255.255.0

        IP Address. . . . . . . . . . . . : fe80::2d0:59ff:feb8:103c%4

        Default Gateway . . . . . . . . . : 10.1.1.254

Tunnel adapter Teredo Tunneling Pseudo-Interface:

        Connection-specific DNS Suffix  . :

        IP Address. . . . . . . . . . . . : fe80::5445:5245:444f%5

        Default Gateway . . . . . . . . . :

Tunnel adapter Automatic Tunneling Pseudo-Interface:

        Connection-specific DNS Suffix  . : 

        IP Address. . . . . . . . . . . . : fe80::5efe:10.1.1.46%2

        Default Gateway . . . . . . . . . :

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands