manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 649

 Chapter 93 OLT Configuration

OLT2406 User’s Guide

649

no interface olt <

aid

>

Removes an OLT configuration for the specified 
interface.

aid

:

 

pon

-<

slot

>-<

port

>

C

13

no interface olt all

Removes all OLT configurations.

C

13

Table 348   OLT Configuration Commands (continued)

COMMAND

DESCRIPTION

M

P

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands