manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 349

 Chapter 43 Maintenance

OLT2406 User’s Guide

349

Alternatively, click 

Save

 on the top right-hand corner in any screen to save the configuration changes 

to the current configuration. 

Note: Clicking the 

Apply

 or 

Add

 button does NOT save the changes permanently. All 

unsaved changes are erased after you reboot the OLT. 

43.5  Reboot System

Reboot System

 allows you to restart the OLT without physically turning the power off. It also allows you to 

load configuration one (

Config 1

) or configuration two (

Config 2

) when you reboot. Follow the steps 

below to reboot the OLT. 

1

In the 

Maintenance 

screen, click a configuration

 

button next to 

Reboot System

 to reboot and load that 

configuration file. The following screen displays.

Figure 214   

Reboot System: Confirmation 

2

Click 

OK

 again and then wait for the OLT to restart. This takes up to two minutes. This does not affect the 

OLT’s configuration.

Click 

Config 1

 and follow steps 1 to 2 to reboot and load configuration one on the OLT.

Click 

Config 2

 and follow steps 1 to 2 to reboot and load configuration two on the OLT.

43.6  Firmware Upgrade 

Use the following screen to upgrade your OLT to the latest firmware. The OLT supports dual firmware 
images, 

Firmware 1

 and 

Firmware 2

. Use this screen to specify which image is updated when firmware is 

uploaded using the web configurator and to specify which image is loaded when the OLT starts up

.

Make sure you have downloaded (and unzipped) the correct model firmware and version to your 
computer before uploading to the device. 

Be sure to upload the correct model firmware as uploading the wrong 

model firmware may damage your device. 

Click 

Management

 > 

Maintenance 

> 

Firmware Upgrade 

to view the screen as shown next. 

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands