Chapter 38 ONT Template
OLT2406 User’s Guide
309
NetworkVID
(SVID/
SPRI:CVID)
Enter the Network Node Interface (NNI) VIDs (1~4094) to which the ONT translates the UNI port
VLAN ID before sending traffic to the OLT. Use a number different from the UNI port VLAN to apply
VLAN translation.
SVID: Service provider VLAN ID
SPRI: Specify the IEEE 802.1p priority level (0-7) for the service provider tag. "0" is the lowest priority
level and "7" is the highest.
CVID: Customer VLAN ID
Ingress Profile
Select the QoS ingress profile to apply to the VLAN’s traffic (IEEE 802.1p priority bit to TC mapping
profile). Click
Ingress Profile Setting
to view the details of the profiles.
TxTag
Sets whether the ONT sends downstream traffic with a VLAN tag (
tag
), a priority tag (
priotag
) or
no tag (
untag
).
AES Encryption Select
Enable
to enable gem port AES encryption.
TR156
Enable or disable TR156 mode. TR156 mode adds a VLAN tag based on the GEM tag of incoming
upstream packets.
Share Priority
Select the share priority in a downstream share group. The value "off" means discard the
downstream share group setting. If other VLANs have "0-7" set in the same downstream share
group, the value cannot be set to "off". The priority value means the priority of VLAN of
downstream rate limit and is unique in the same downstream bandwidth group. 7 has the highest
priority.
MAC Number
You can set the maximum number (1-6) of metered downstream MAC addresses per GEM port.
Excess MAC addresses can transmit traffic without bandwidth metering.
If the share priority in a downstream share group is not selected in the
Share Priority
field, there’s
no limitation of metered downstream MAC addresses per GEM port.
PBit Profile
Select a priority bit profile to apply to this traffic class. Click
Pbit Profile Setting
to view the details of
the profiles.
PVID (/PRI)
Select the priority level (0~7) to apply to the VLAN’s traffic. Select
None
to not set a priority level
tag value.
Protocol-
based Vlan
(Ether Type/
PRI)
Use this section to apply the VLAN flow setting to specific protocols of packets. The system
converts it to the corresponding Ethernet type as follows:
IPoE packet ethertype = 0x0800
PPPoE packet ethertype = 0x8863 , 0x8864
ARP packet ethertype = 0x0806
IPv6 packet ethertype = 0x86DD
Select the priority bit the ONT inserts into the protocol packets.
Add
Click
Add
to add a UNI port VLAN entry.
Cancel
Click
Cancel
to clear the fields.
Clear
Click
Clear
to return the screen’s settings to the defaults.
Index
This is the index number of a UNI port VLAN flow setting.
AID
This is the UNI port’s ID in the format: uniport-<pon>-<ont>-<card>-<port>.
Active
This displays whether the UNI port VLAN flow setting is active (
Y
) or not (
N
).
UNIVID
This displays the UNI SVID and CVID of traffic on the UNI port to which the VLAN flow settings
apply.
NetworkVID
This displays the NNI VIDs to which the ONT translates the UNI port VLAN ID before sending traffic
to the OLT.
Ingress Profile
This displays the QoS ingress profile the VLAN flow applies to the VLAN’s traffic (IEEE 802.1p priority
bit to TC mapping profile).
Table 134 Advanced Application > ONT Template > Uniport VLAN (continued)
LABEL
DESCRIPTION
Summary of Contents for OLT2406
