manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 543

 Chapter 76 Multicast

OLT2406 User’s Guide

543

The following table describes the commands for IGMP snooping VLAN.  

76.7  MVR Overview 

Multicast VLAN Registration (MVR) is designed for applications (Such as Media-on-Demand (MoD)) that 
use multicast traffic across an Ethernet ring-based service provider network. 

MVR allows one single multicast VLAN to be shared among different subscriber VLANs on the network. 
While isolated in different subscriber VLANs, connected devices can subscribe to and unsubscribe from 
the multicast stream in the multicast VLAN. This improves bandwidth utilization with reduced multicast 
traffic in the subscriber VLANs and simplifies multicast group management. 

MVR only responds to IGMP join and leave control messages from multicast groups that are configured 
under MVR. Join and leave reports from other multicast groups are managed by IGMP snooping. 

The following figure shows a network example. The subscriber VLAN (

1

, 

3

, and 

4

) information is hidden 

from the streaming media server, 

S

. In addition, the multicast VLAN information is only visible to the OLT 

and 

S

. 

Table 278   IGMP Snooping VLAN Commands

COMMAND

DESCRIPTION

M

P

show igmp-snooping vlan

Displays the VLANs on which IGMP snooping is 
enabled.

E

3

igmp-snooping vlan mode 

<auto|fixed>

Specifies how the VLANs on which the OLT 
snoops IGMP packets are selected.

auto

: The OLT learns multicast group 

membership on any VLAN. The OLT drops any 
IGMP control messages on other VLANs after it 
reaches this maximum number (

auto

 mode).

fixed

: The OLT only learns multicast group 

membership on specified VLAN(s). The OLT 
drops any IGMP control messages for any 
unspecified VLANs (

fixed

 mode). 

C

13

igmp-snooping vlan <

vlan-id

> 

Specifies which VLANs to perform IGMP 
snooping on if the mode is 

fixed

. Optionally, 

sets a name for the multicast VLAN.

C

13

no igmp-snooping vlan <

vlan-id

>

Removes IGMP snooping configuration on the 
specified VLAN if the mode is 

fixed

.

C

13

clear multicast vlan all

Removes all multicast VLAN counters.

E

3

clear multicast vlan <

vid

>

Removes multicast VLAN counter of the 
specified VLAN.

E

13

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands