manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 688

Chapter 97 Management Switching Card Control

OLT2406 User’s Guide

688

C

HAPTER

 97

Management Switching

Card Control

97.1  Management Switching Card Control Overview

This chapter describes management switching card redundancy status and control commands.

The OLT can use two management switching cards. If one management switching card fails, the other 
one becomes active and takes over. 

97.2  Management Switching Card Control Commands

The following section lists the commands for this feature.

Table 364   Management Switching Card Control Commands

COMMAND

DESCRIPTION

M

P

show msc

Displays management switching card state and 
firmware version information from execution 
mode.

E

3

msc <cr>

Displays management switching card state and 
firmware version information from configuration 
mode.

C

13

msc sync ras

Synchronizes the running firmware on the 
standby management switching card with the 
running firmware on the active management 
switching card. 

C

13

msc update-target [ standby | all ]

Has the OLT apply firmware and romfile updates 
by FTP or TFTP.

Sets the update target to apply to only the 
standby management switching card or all 
management switching card cards.

C

13

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands