manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 580

Chapter 78 VoIP

OLT2406 User’s Guide

580

4

Click 

VoIP > SIP > SIP Account 

and check that the SIP account is active. Check that the SIP account 

number, user name and password are configured (these depend on the SIP server’s configuration). 

5

Click 

Status 

and check the account status. It displays 

Registered

 if the PMG5318 can register the SIP 

account with the SIP server. 

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands