manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 317

 Chapter 38 ONT Template

OLT2406 User’s Guide

317

The following table shows some common protocol types and the corresponding protocol number. Refer 
to 

http://www.iana.org/assignments/protocol-numbers

 for a complete list.   

Some of the most common TCP and UDP port numbers are: 

See 

Appendix B on page 750

 for information on commonly used port numbers.

38.2.6.2  ONT ACL Profile Counter

Use this screen to display the dropped packets counters of the selected ACL profile(s) and ONT(s). 

Click 

ONT ACL Profile Counter

 in the 

Advanced Application

 > 

ONT Template > ONT ACL > ACL Profile 

Setting

 screen to display the screen as shown.

Figure 192   

Advanced Application > ONT Template > ONT ACL > ACL Profile Setting > ONT ACL Profile 

Counter

Table 139   Common IP Protocol Types and Protocol Numbers

PROTOCOL TYPE

PROTOCOL NUMBER

ICMP

1

TCP

6

UDP

17

EGP

8

L2TP

115

Table 140   Common TCP and UDP Port Numbers

PROTOCOL NAME

TCP/UDP PORT NUMBER

FTP

21

Telnet

23

SMTP

25

DNS

53

HTTP

80

POP3

110

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands