manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 675

 Chapter 96 Remote ONT

OLT2406 User’s Guide

675

96.4.2  UNI Port Queue Settings

Use the 

queue

 command to configure a UNI port traffic class.

Table 355   UNI Port QoS Queue Command Parameters

LABEL

DESCRIPTION

M

P

remote uniport <

aid

>

Configures UNI port settings.

aid

: 

uniport-<

slot

>-<

pon

>-<

ont

>-<

card

>-

<

port

>

C

13

queue tc <

tc

> priority 

<

priority

> weight <

weight

> 

usbwprofname <

usbwprofname

> 

dsbwprofname <

dsbwprofname

> 

dsoption <

dsoption

> 

bwsharegroupid 

<

bwsharegroupid> 

[<

dsbwsharegroupid

>]

Configures a UNI port QoS queue.

tc

: The IEEE 802.1P QoS traffic class 0~7 of traffic 

to which to apply this queue. 

priority

: 0~7. This is reserved for future 

development since the Zyxel ONTs do not 
support this QoS feature now. 

weight

: Queue weight: 0~255. You can 

configure different queues with the same queue 
priority level. The OLT then uses Weighted Round 
Robin (WRR) scheduling to service these queues 
on a rotating basis based on their queue weight. 
The higher a queue’s weight, the more service it 
gets. This is reserved for future development 
since the Zyxel ONT do not support this QoS 
feature now. 

usbwprofname

: The upstream bandwidth 

profile to use for the traffic class.

dsbwprofname

: The downstream bandwidth 

profile to use for the traffic class.

dsoption

: 

olt|ont

. Set whether to apply the 

downstream rate limit function to the OLT (olt) or 
the ONT (ont).

bwsharegroupid

: Specify the ID (1-40) of the 

bandwidth group on this ONT to put the QoS 
queues into. You created the bandwidth group 
when you configured the ONT setup. The UNI 
port will share the bandwidth defined by the 
bandwidth group.

dsbwsharegroupid

: Specify the ID (1-40) of 

the downstream bandwidth group on this ONT 
to put the QoS queues into. You can use this 
when the 

dsoption

 is 

olt

. You created the 

bandwidth group when you configured the ONT 
setup. The UNI port will share the downstream 
bandwidth defined by the bandwidth group. 
The OLT uses 

bwsharegroupid

 as the default 

value.

C

13

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands