manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 648

OLT2406 User’s Guide

648

register-method template-option 
<

template-number

>

Creates an olt OLT PON register method 
template (onu-121~128).

template-number

: 121~128

C

13

rei-counter-th <

threshold

>

Sets the Remote Error Indication (REI) counter 
threshold.

threshold

: 0~4294967295

C

13

tca-status <0|1>

Disables or enables the low rate Threshold 
Crossing Alert (TCA) alarm. 

0: disable

1: enable

C

13

transceiver <

type

>

Sets the PON link’s transceiver type (0~22).

Transceiver types:

0: LIGENT

1: LUMINENT

2: FIBERXON

3: FUJITSU

4: LIGENT_A

5: LIGENT_B

6: LUMINENT_A

7: LUMINENT_B

8: FIBERXON_A

9: FUJITSU_A

10: NEC 

11: NEOPTEC 

12: LIGENT_C 

13: FIBERXON_B

14: FUJITSU_30537

15: NEOPHOTONICS_A

16: NEOPHOTONICS_B

17: NEOPHOTONICS_C

18: SUPERXON

19: WTD

20: DELTA

21: 1

22: 2

C

13

transceiver tx-disable <0|1>

Disables the PON link transceiver’s transmission.

0: enable

1: disable

C

13

Table 348   OLT Configuration Commands (continued)

COMMAND

DESCRIPTION

M

P

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands