manualshive.com logo in svg

ZyXEL Communications OLT2406, User Manual

Share
Download
ZyXEL Communications OLT2406 User Manual Download Page 693

 Chapter 98 Port Protection Switching

OLT2406 User’s Guide

693

Figure 292   

Downlink Port Protection Switching  

The following section lists the commands for this feature.

Table 367   Downlink Port Protection Switching Commands

COMMAND

DESCRIPTION

M

P

show protect-switch pon status

Displays the current status of the downlink PON 
port protection switching operation. 

E

3

switch-over pon <

aid

>

Triggers a PON port protection switch-over 
operation.

aid

: pon-<

slot

>-<

pon

>

E

13

protect-switch pon pon-<

slot

>-

<

port

> pon-<

slot

>-<

port

>

Assigns the specified downlink PON ports as an 
active and backup pair. You can configure 
multiple pairs of PON ports, but each PON port 
can only be in one pair at a time.

pon pon-<slot>-<port>

 is the active port, and 

pon-<slot>-<port>

 is the standby port.

C

13

Working path

Backup path

Traffic from

uplink

Summary of Contents for OLT2406































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands