STEERING AND FRONT SUSPENSION
Steering Column
2007-2008 XRT 800, 810 and 850 Maintenance and Service Manual
Page 7-5
7
3. Install the wedge (16), spring (15), washer (14), and snap ring (13) onto the bottom end of the steering
shaft (19)
(Figure 7-4, Page 7-5)
.
4. Insert the shaft (19) from the bottom of the steering tube (20)
(Figure 7-3, Page 7-3)
.
5. Turn the assembly over and place the shaft (19) on a bench. Install the wedge (16) and retaining ring (22)
onto the top of the shaft
(Figure 7-5, Page 7-5)
. Be sure the prongs on the retaining ring face up and
away from the wedge. Use a steering column retaining ring tool (CCI P/N 1014259) to seat the retaining
ring to the proper depth. Support end of tube while pressing. If you do not have the recommended tool,
use the same tube as was used in step 2 to press the retaining ring onto the top of the shaft. The retaining
ring should be pressed onto the shaft until 2 to 2-1/8 inches (5.1-5.4 cm) of the shaft extends from the
top of the bearing seat in the steering tube
(Figure 7-5, Page 7-5)
.
STEERING COLUMN INSTALLATION
1. Install boot (12). Reinstall mount (4 and 5) onto the end of the steering column. Tighten bolts (6) to 20
ft-lb (27 N·m)
(Figure 7-3, Page 7-3)
.
2. For ease of assembly and to prevent corrosion, apply a light coat of anti-seize or lubricating compound
to both splined ends of the steering shaft.
3. Position the steering column assembly in the vehicle while inserting the steering column shaft into the
upper universal joint (1). The flat portion of the steering shaft spline (19) must be aligned with the bolt hole
in the universal joint (1) before sliding the spline into the universal joint. While holding the steering col-
umn in place, attach it to the frame using bolts (8) washers (7) and nuts (9)
(Figure 7-3, Page 7-3)
.
Thread the nuts onto the bolts but do not tighten them.
4. Reinstall washers (29 and 11) and screw (10). Tighten to 20 ft-lb (27 N·m).
5. Install the bolt (2) and lock washer (3) on the upper universal joint and finger-tighten.
6. Tighten the two nuts (9) and bolts (8) to 17 ft-lb (23 N·m).
7. Tighten the bolt (2) on the upper universal joint to 15 ft-lb (20 N·m).
Figure 7-4 Steering Shaft – Bottom End
Figure 7-5 Steering Shaft – Top End
WEDGE SEATING
INTO THE INNER
RACES OF BEARING
BEARING
PRESS TOOL
(CCI P/N 1014264)
18
20
19
17
13
14
15
18
16
STEP 1
STEP 2
STEP 3
2-2 1/8 inches
(5.1-5.4 cm)
COLUMN
RETAINING TOOL
(CCI P/N 1014259)
WEDGE SEATING
INTO THE INNER
RACES OF BEARING
BEARING
PRESS TOOL
(CCI P/N 1014264)
22
20
16
16
17
18
STEP 1
STEP 2
STEP 3
19
Summary of Contents for 2007 XRT 800
