![background image](http://html1.mh-extra.com/html/club-car/2007-xrt-800/2007-xrt-800_maintenance-service-manual_2626829049.webp)
BODY AND TRIM
Floor Mat
2007-2008 XRT 800, 810 and 850 Maintenance and Service Manual
Page 4-19
4
REAR BODY INSTALLATION
1. Install in reverse order of removal.
1.1. Tighten kick-plate nuts to 48 in-lb (5.4 N·m) while holding the kick-plate screws
(Figure 4-19,
Page 4-16)
.
1.2. Tighten two screws (1) and lock nuts located under rear body to 20 in-lb (2.3 N·m)
(Figure 4-18,
Page 4-16)
.
1.3.
Gasoline vehicles only:
1.3.1. Install fuel pump.
See Fuel Pump Installation on page 16-21.
1.3.2. Check the choke positioner for proper adjustment on gasoline-powered vehicles and
adjust if necessary.
1.4.
Electric vehicles only:
1.4.1. If necessary, install the charger receptacle and tighten the four screws to 16 in-lb (1.8 N·m)
(Figure 4-16, Page 4-13)
. Tighten the nut that secures the 10-gauge black wire to the
charger receptacle to 23 in-lb (2.6 N·m).
Vehicles Equipped with Rear Facing Seat:
1.5. Tighten hardware (12) attaching the front legs of the seat back support assembly to the chassis to
120 in-lb (13.6 N·m)
(Figure 4-20, Page 4-17)
.
1.6. Tighten the hardware (13) attaching the rear legs of the seat back support assembly to the chassis
to 11 ft-lb (14.9 N·m).
1.7. Tighten the hardware (10, 7 and 1) to 124 in-lb (14 N·m).
1.8. Tighten the hardware (8) securing the rear seat support (9) to the chassis to 108 in-lb (12.2 N·m).
1.9. Tighten the hardware (4) to 65 in-lb (7.35 N·m).
Vehicles Equipped with Cargo Bed:
1.10. Tighten the bolts (6) attaching the seat back supports (8) to the chassis to 156 in-lb (17.6 N·m)
(Figure 4-21, Page 4-18)
.
1.11. Tighten the nuts (3) securing the cargo bed support (1) to the chassis to 108 in-lb (12.2 N·m).
1.12. Install seat bottom.
FLOOR MAT
See General Warning on page 1-1.
FLOOR MAT REMOVAL
1. Remove the brake and accelerator pedals.
See Section 5 – Accelerator and Brake Pedal Group.
2. Slide the mat from under the edge of the rear body. Loosen the rear body screws if necessary.
3. Slide the mat away from the trim up under the dash and remove the floor mat.
FLOOR MAT INSTALLATION
1. Reverse the removal procedure to install the floormat. If loosened, tighten rear body screws to 48 in-lb
(5.4 N·m).
2. Install the brake and accelerator pedals.
See Section 5 – Accelerator and Brake Pedal Group.
Summary of Contents for 2007 XRT 800
