![background image](http://html1.mh-extra.com/html/club-car/2007-xrt-800/2007-xrt-800_maintenance-service-manual_2626829395.webp)
ELECTRICAL SYSTEM AND TESTING: ELECTRIC VEHICLE
Troubleshooting
2007-2008 XRT 800, 810 and 850 Maintenance and Service Manual
Page 21-31
21
3.2. Place the Forward/Reverse switch in the FORWARD position. The handset should indicate that
FORWARD INPUT is ON. If the handset indicates any other reading, check vehicle wiring.
See Wir-
ing Diagram on page 21-2.
Also check the 16-pin connector at the speed controller.
See Test Pro-
cedure 9 – 16-Pin Connector on page 21-18.
4. Test REVERSE INPUT.
4.1. Access the Test menu and select REVERSE INPUT by using the SCROLL DISPLAY buttons. The
handset should indicate OFF when the Forward/Reverse switch is in the NEUTRAL or FORWARD
position.
4.2. Place the Forward/Reverse switch in the REVERSE position. The handset should indicate that
REVERSE INPUT is ON. If the handset indicates any other reading, check vehicle wiring.
See Wir-
ing Diagram on page 21-2.
Also check the 16-pin connector at the speed controller.
See Test Pro-
cedure 9 – 16-Pin Connector on page 21-18.
5. If the handset displays readings other than those described above and the wiring is found to be correct,
proceed to the following procedure, Forward/Reverse Rocker Switch Test without the Diagnostic Hand-
set.
Forward/Reverse Rocker Switch Test without the Diagnostic Handset
1. Disconnect the battery cables as instructed.
See WARNING “To avoid unintentionally starting...” in
General Warning on page 1-1.
2. Remove the rocker switch from the vehicle.
See Section 23 – Electrical Components: Electric Vehi-
cle.
3. Disconnect the three wires from the rocker switch. Using a multimeter set to 200 ohms, place the black
(–) probe on the blue wire terminal 3 position on the rocker switch, and place the red (+) probe on the
orange wire terminal 2 position. With the switch in NEUTRAL or REVERSE, there should be no conti-
nuity. With the switch in FORWARD, there should be continuity. If the readings are incorrect, replace the
switch.
4. Place the black (–) probe on the brown wire terminal 1 position on the rocker switch and place the red
(+) probe on the orange wire terminal. With the switch in REVERSE, there should be continuity. If the
readings are incorrect, replace the switch.
TEST PROCEDURE 16 – REVERSE BUZZER
See General Warning on page 1-1.
1. Disconnect the battery cables as instructed.
See WARNING “To avoid unintentionally starting...” in
General Warning on page 1-1.
2. Remove the instrument panel.
2.1. Loosen seven Tuflok screws, but do not remove screws completely, as shown in Detail A.
See Figure 23-1, Page 23-2.
2.2. Remove Tuflok screws from instrument panel as shown in Detail B.
2.3. Pull forward on top of instrument panel.
3. Disconnect the 18-gauge red and orange/white wires from the reverse buzzer.
4. Place the Tow/Run switch in the TOW position and connect the battery cables, positive (+) cable first.
Tighten battery terminals to 110 in-lb (12.4 N·m).
5. Place the Tow/Run switch in the RUN position.
6. Set a multimeter to 200 volts DC. Place the black (–) probe on battery no. 4 negative post and place the
red (+) probe on the red wire terminal end that was disconnected from the reverse buzzer. The reading
should be approximately 48 volts (full battery voltage).
Summary of Contents for 2007 XRT 800
