APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download | Manualshive

Page: 122 / 379

background image

Level in electrical circuit diagram: engine s

pe-

ed sensor

Location:

•

on the vehicle: inside the flywheel cov-

er

•

connector (if available): near the Mar-

elli control unit

Electrical characteristics:

•

Resistance at ambient temperature:

130 +/- 20 Ohm

Pin-out:

1. Negative signal

2. Positive signal

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

NAVIGATOR: PARAMETERS

Engine rpm

NAVIGATOR: STATUSES

Synchronised panel

Example value:

Start-up_Lean_Rich_Fault due to rich value_Fault due to lean value

If the probe connector is removed (voltage almost equal to zero), the status is Fault due to lean value

Example value:

No_under analysis_standby_Yes

The parameter refers to the engine revs signal: in case the signal has not been correctly identified yet,

the under analysis or standby statuses may be displayed.

NAVIGATOR: ACTIVATION

-

NAVIGATOR: ELECTRICAL ERRORS

-

CAUTION

IF THE ELECTRIC CIRCUIT IS INTERRUPTED OR SHORT-CIRCUITED OR NO ERROR IS DIS-
PLAYED, CHECK THE ENGINE SPEED SENSOR CONNECTOR AND THE MARELLI CONTROL
UNIT CONNECTOR: IF NOT OK, RESTORE; IF OK, CHECK THE SENSOR ELECTRIC CHARAC-
TERISTIC IS THE CORRECT ONE: IF IT IS NOT, REPLACE THE SENSOR. IF IT IS THE CORRECT
ONE, CHECK THAT THERE IS CONTINUITY ON BOTH CABLES, SUPPLY INSULATION AND
GROUND CONNECTION INSULATION. CARRY OUT THE TESTS FROM THE SENSOR CONNEC-
TOR TO THE SENSOR. IF NOT OK, RESTORE THE CABLE HARNESS/REPLACE THE SENSOR.
IF OK, PERFORM THE TEST FROM PINS 9 AND 23 OF THE MARELLI CONTROL UNIT ENGINE
CONNECTOR.

NAVIGATOR: LOGIC ERRORS

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 122

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
120
121
122
123
124
...
»

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

Brand: GAS GAS Pages: 57

Brand: Evotech Pages: 84

990D0-44G00-ALM

Brand: Suzuki Pages: 24

Brand: Big Dog Pages: 100

Brand: PIAGGIO Pages: 275

Brand: AGV Pages: 64

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 100

Road Star XV17AWX

Brand: Yamaha Pages: 110

Brand: Yamaha Pages: 650

Brand: KTM Pages: 7

Brand: X&I Pages: 59

Brand: DYNATEK Pages: 5

Brand: hepco & becker Pages: 2

Brand: hepco & becker Pages: 3

Brand: Race Dynamics Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands