manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

The Aprilia Dorsoduro Factory ABS 2011 is a high-performance motorcycle built for thrilling rides. To ensure its optimal maintenance and care, download the free Service Station Manual from manualshive.com to access comprehensive instructions and guidelines. This manual is essential for any Dorsoduro owner seeking to maximize their riding experience.

Share
Download
background image

•

Tighten the three screws on the intake

and discharge sides.

•

Screw the two head fixing screws lo-

cated inside the timing chain compart-

ment.

•

Check that the intermediate gear pin

lubrication holes are clean.

•

With a hook, hold the timing chain.

•

Fit the timing chain on the intermediate

gear.

•

Slide in the pin together with a new O-

Ring and a washer.

•

Check that the axial clearance be-

tween the pin and the gear is between

0.30 and 0.60 mm (0.0118 - 0.0236 in).

Engine

DORSODURO FACTORY ABS

ENG - 230

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

R&G CP0504BL Fitting Instructions Manual preview
CP0504BL
Brand: R&G Pages: 10
Suzuki 990D0-31J50-CLE Installation Instructions Manual preview
990D0-31J50-CLE
Brand: Suzuki Pages: 12
Serpento COYOTE 250 User Manual/Maintenance preview
COYOTE 250
Brand: Serpento Pages: 66
BMS MachoMan Assembly Instructions Manual preview
MachoMan
Brand: BMS Pages: 11
APRILIA SR 50 Manual preview
SR 50
Brand: APRILIA Pages: 151
Beta RR 4T ENDURO 2014 350 Catalogue Of Spare Parts preview
RR 4T ENDURO 2014 350
Brand: Beta Pages: 66
Beta Urban 125 Service Manual preview
Urban 125
Brand: Beta Pages: 74
Beta Rev 3 2006 Owner'S Manual preview
Rev 3 2006
Brand: Beta Pages: 148
hepco & becker 6617569 01 01 Manual preview
6617569 01 01
Brand: hepco & becker Pages: 4
Protekt ATRA 10 Quick Start Manual preview
ATRA 10
Brand: Protekt Pages: 4
APRILIA PEGASO 650 IE - 2003 Manual preview
PEGASO 650 IE - 2003
Brand: APRILIA Pages: 112
APRILIA Pegaso 650 I.E. Use And Maintenance Book preview
Pegaso 650 I.E.
Brand: APRILIA Pages: 112
APRILIA PEGASO 650 FACTORY Manual preview
PEGASO 650 FACTORY
Brand: APRILIA Pages: 197
KTM 1050 RR kit Installation Manual preview
1050 RR kit
Brand: KTM Pages: 10
KTM 350 SX-F 2017 Setup Instructions preview
350 SX-F 2017
Brand: KTM Pages: 22
KTM 60312935044 Information preview
60312935044
Brand: KTM Pages: 12
KTM PowerParts 44011076140 Manual preview
PowerParts 44011076140
Brand: KTM Pages: 17
Royal Enfield Classic 350 BS IV Owner'S Manual preview
Classic 350 BS IV
Brand: Royal Enfield Pages: 108

Brands by name

Popular brands

Load more brands