APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 13 / 379

Engine

ENGINE

Specification

Desc./Quantity

Model

M551M

Type

90° longitudinal V-twin, 4-stroke, 4 valves per cylinder, 2 over-

head camshafts.

No. of cylinders

Total engine capacity

749.9 cm³ (45.76 cu.in)

Bore / stroke

92 x 56.4 mm (3.62 x 2.22 cu.in)

Intake valve clearance

0.11 - 0.18 mm (0.0043 - 0.0071 in)

Exhaust valve clearance

0.16 - 0.23 mm (0.0063 - 0.0091 in)

Compression ratio

11.0: 1

Ignition

starter

Engine idle speed

1400 ± 100 rpm

Clutch

Multiple-disk, oil-bathed clutch with control on the left side of

the handlebar

Lubrication system

Wet crankcase. Pressure system regulated by a trochoidal

pump

Air filter

With dry cartridge filter

Cooling

Fluid

EARBOX

Specification

Desc./Quantity

Type

Mechanical, 6 speeds with foot lever on the left hand side of

the engine

Transmission

EAR

RATIOS

Specification

Desc./Quantity

Gear ratio

Gear primary drive 38/71

1st gear ratio

14/36 (secondary)

2nd gear ratio

17/32 (secondary)

3rd gear ratio

20/30 (secondary)

4th gear ratio

22/28 (secondary)

5th gear ratio

23/26 (secondary)

6th gear ratio

24/25 (secondary)

Final drive gear ratio

16/46

Capacities

APACITY

Specification

Desc./Quantity

Fuel capacity (reserve included)

12 l (2.64 UKgal; 3.17 US gal)

Fuel reserve

2.8 l (0.62 UKgal; 0.74 US gal)

Engine oil

3.0 l (without oil filter change) (0.66 UKgal; 0.79 USgal)

3.2 l (with oil filter change) (0.70 UKgal; 0.85 USgal)

Fork oil (check also the correct air level in the stem)

494 cm³ (RIGHT stem) (30.14 cu.in)

494 cm³ (LEFT stem) (30.38 cu.in)

Coolant

1.8 l (0.40 UKgal; 0.48 USgal)

Seats

Maximum weight limit

400 kg (882 lb)

DORSODURO FACTORY ABS

Characteristics

CHAR - 13

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands