APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 188 / 379

EAR

SELECTOR

pos.

Description

Type

Quantity

Torque

Notes

Gear retainer pawl fastener screw

12 Nm (8.85 lbf ft)

Selector plate fastener screw

5.50 Nm (4.06 lbf ft)

Screw fastening Desmodromic se-

lector drum / Selector sprocket

23 Nm (16.96 lbf ft)

Gear sensor fastener screw

5.50 Nm (4.06 lbf ft)

Loctite 243

Selector pin fastener onto clutch side

crankcase half

M10x1.5

16 Nm (11.80 lbf ft)

Tightening tone wheel on secondary

gearbox

M16x1

43 Nm (31.72 lbf ft)

Loctite 270

Removing the gear selector

To remove the gear selector refer to the operations described under Crankcase opening.

Checking the gear selector

Selector spring

Make sure that the spring ends on the two shifting

positions (forward = downshifting and backward =

up-shifting) are always in contact with the selector

plate

Make sure that the clearance between the end of

the spring on the selector plate and the stop pin is

almost null, when in home position (see diagrams)

Pawl

Make sure that both pawl tips run free, without

jamming

Selector plate spring

With a thickness gauge, check that the spring is

not deformed by over-stretching.

Engine

DORSODURO FACTORY ABS

ENG - 188

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands