APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download Page 337

Page: 337 / 379

Water pump

ATER

PUMP

pos.

Description

Type

Quantity

Torque

Notes

Clutch side cover fastener screw

13 Nm (9.59 lbf ft)

Fastener screw for Pump Cover /

Clutch side cover

13 Nm (9.59 lbf ft)

Screw fastening Pump Cover /

Clutch Cover / clutch side crankcase

half

13 Nm (9.59 lbf ft)

Nut fastening pump drive input gear

on shaft

12 Nm (8.85 lbf ft)

Loctite 244

Water pump rotor

4.50 Nm (3.32 lbf ft)

Removal

COVER REMOVAL

•

Drain off the cooling circuit completely.

•

Undo and remove the five screws.

•

Remove the water pump cover.

PUMP ROTOR REMOVAL

•

Remove the clutch-side cover.

•

Lock the pump shaft with a universal wrench on the hexagonal insert on the shaft.

DORSODURO FACTORY ABS

Cooling system

COOL SYS - 337

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Brands by name

Popular brands