APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download Page 74

Page: 74 / 379

•

Shut off the engine.

•

Keep the vehicle upright with both

wheels on the ground.

•

Check the correct oil level through the

appropriate sight glass on the engine

crankcase.

MAX

= maximum level.

MIN

= minimum level

•

The oil level is correct when it is close

to the "MAX" reference.

Replacement

Check the engine oil level frequently.

To change the oil:

CAUTION

HOT OIL IS MORE FLUID AND WILL DRAIN OUT MORE EASILY AND COMPLETELY; IDEAL
TEMPERATURE IS REACHED AFTER THE ENGINE HAS RUN FOR ABOUT TWENTY MINUTES.

OIL BECOMES VERY HOT WHEN THE ENGINE IS HOT; BE CAREFUL NOT TO GET BURNED
WHEN CARRYING OUT THE OPERATIONS DESCRIBED BELOW.

•

Use a cloth to wipe off any mud deposit

on the area next to the filler plug (1).

•

Place a container with + 4000 cm³ (244

cu.in) capacity under the drainage plug

(2).

•

Unscrew and remove the drainage

plug (2).

•

Unscrew and remove the filler plug (1).

•

Drain the oil into the container; allow

several minutes for oil to drain out com-

pletely.

•

Replace the sealing washer of the

drainage plug (2).

•

Remove any metal scrap attached to

the drainage plug (2) magnet.

•

Screw and tighten the drainage plug

(2).

Maintenance

DORSODURO FACTORY ABS

MAIN - 74

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Brands by name

Popular brands