APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download | Manualshive

Page: 304 / 379

background image

•

Working from the left side, unscrew

and remove the nut and collect the

washer.

REMOVAL SHOULD BE CARRIED OUT WITH UTMOST
CAUTION.
SUPPORT THE SWINGARM FROM THE FRONT TO AVOID
ACCIDENTAL FALLS.
PLACE A WOODEN SUPPORT UNDER THE FRONT PART
OF THE REAR SWINGARM TO PREVENT IT FROM LOW-
ERING AND TO KEEP IT UPRIGHT.

•

Working on the right side, unscrew and

remove the swingarm bolt.

UPON REMOVING THE REAR SWINGARM PAY ATTEN-
TION NOT TO JAM THE GEARING CHAIN.

See also

Removing the

rear wheel

Drive chain

Adjusting

The vehicle is fitted with an endless chain, without master link.

NOTE

CARRY OUT MAINTENANCE OPERATIONS AT HALF THE INTERVALS SPECIFIED IF THE VE-
HICLE IS USED IN PARTICULAR RAINY OR DUSTY CONDITIONS, OFF ROAD OR FOR TRACK
USE.

To check clearance:

•

Shut off the engine.

•

Place the vehicle on the service stand.

•

Engage neutral gear.

•

Check that the vertical oscillation at a

point between the pinion and the crown

on the lower branch of the chain is ap-

prox. 25 - 30 mm (0.98 - 1.18 in).

•

Move the vehicle forward so as to

check vertical oscillation in other posi-

Chassis

DORSODURO FACTORY ABS

CHAS - 304

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
302
303
304
305
306
...
»

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

Zero S Series 2014

Brand: Zero Motorcycles Pages: 128

Freeride E-XC 2019

Brand: KTM Pages: 44

Brand: yasuni Pages: 12

Brand: GAS GAS Pages: 150

V 7 CAFE CLASSIC

Brand: MOTO GUZZI Pages: 147

Brand: Triumph Pages: 53

Brand: BMW Pages: 241

Brand: Yamaha Pages: 9

Brand: Yamaha Pages: 50

Brand: Yamaha Pages: 91

Brand: Yamaha Pages: 92

Virago XV250 2004

Brand: Yamaha Pages: 95

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 104

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 114

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands