APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 16 / 379

Supply

UEL

SYSTEM

Specification

Desc./Quantity

Type

Electronic injection (Multipoint)

Throttle valve diameter

Ø 52 mm (2.05 in)

Fuel

Premium unleaded petrol, minimum octane rating 95 (NORM)

and 85 (NOMM)

Tightening Torques

Chassis

Front side

OOLING

SYSTEM

pos.

Description

Type

Quantity

Torque

Notes

Fan fastener screw

3 Nm (2.21 lbf ft)

Flanged TE screw fixing LH side ra-

diator to trellis frame and radiator

bracket to engine

M6x25

10 Nm (7.37 lbf ft)

Characteristics

DORSODURO FACTORY ABS

CHAR - 16

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands