APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 286 / 379

•

Insert the washer that will be supported

on the spring

•

Insert and hand tighten the nut on the

pumping member pin

•

Place the preload pipe.

•

Tighten the appropriate tool on the

pumping member pin rod and keep it

raised to allow, inserting a wrench in

the nut by compressing the spring.

Specific tooling

020890Y

Pumping member stanchion support

rod

8140147

Spacer tool

•

Tighten the nut as much as possible.

•

Insert the cover and tighten until it

stops.

•

Remove the specific tools.

•

Screw the cover in the sleeve to the

prescribed torque.

Filling oil

•

Place the sleeve upright in a vice fitted with protection shoes.

•

Compress the sleeve in the stem. Place a support under the stem in order to leave it com-

pressed.

•

Pour part of the fork oil into the sleeve.

•

Wait some minutes until the oil fills all the ducts.

Suspensions

DORSODURO FACTORY ABS

SUSP - 286

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands